ROFF Crocodile Tiling FAQ Banner
Roff FAQ Banner Mobile

FAQs

How do I tile a swimming pool using tile adhesive?

Tiling a swimming pool with Roff products requires full, void-free adhesive coverage beneath every tile, since any trapped air pockets can lead to tiles lifting under sustained water pressure once the pool is filled. The joints then need to be finished with a fully water-resistant, chemical-resistant grout, such as Roff Rainbow Tile Mate Epoxy Grout, to prevent water ingress through the joints over time. Given the specialised, continuous-immersion conditions of pool tiling, it’s advisable to consult a Roff technical expert before starting this type of project.

How do I use tile adhesive for swimming pool tiles?

Swimming pool tiling with Roff products requires particular attention to continuous water immersion, so the tile adhesive should be paired with a fully water-resistant grout such as Roff Rainbow Tile Mate Epoxy Grout, which is stain-free, crack-free and chemical-resistant, to seal the joints against constant moisture. The adhesive itself should be applied with full coverage beneath each tile to avoid trapped air pockets that can lead to tiles lifting under water pressure over time. Given the specialised conditions of pool tiling, consulting a Roff technical expert before starting is recommended.

How do I use tile adhesive to fix tiles on ceramic countertops?

Roff Master Fix Adhesive is a suitable choice for fixing ceramic tiles onto a countertop base, since countertops are often built on plywood, cement board or other non-traditional substrates rather than plastered masonry. Full adhesive coverage under each tile is especially important on countertops, since these surfaces see regular contact, weight and moisture from daily use. Once the tiles are set and cured, grouting with a water-resistant or epoxy-based product such as Roff Starlike helps keep the countertop surface hygienic and easy to clean.

Which adhesive is best for granite countertops?

Roff Master Fix Adhesive, formulated for engineered stones and other non-traditional substrates, is a suitable option for fixing granite countertop pieces, given the weight and rigidity of granite compared with standard floor or wall tiles. For sealing and joining granite slab sections, Tenax Eliox A+B, an epoxy-based clear mastic, is commonly used to fill joints and repair any gaps between granite pieces, while Tenax Proseal can be applied afterward to protect the finished countertop surface from staining and moisture.

Which adhesive is best for outdoor tiles?

Roff Extrofix Adhesive is designed for outdoor tiling, including external cladding using ceramic tiles, marble and natural stone on exterior surfaces exposed to sun, rain and temperature changes. Outdoor installations need an adhesive with strong weather resistance and flexibility to handle thermal expansion and contraction over time, which Roff Extrofix is formulated to withstand. For outdoor areas that also experience vibration, such as elevated decks or facades near traffic, Roff Extrofix Ultra offers additional high-tensile strength for a more secure, long-lasting bond.

Which Roff adhesive is suited to fixing outdoor patio stones?

Roff Extrofix Ultra is designed for exterior areas prone to vibration and offers high tensile strength, making it a good fit for outdoor patio stone installations that face foot traffic, temperature swings and outdoor weathering over time. Patio stones are often heavier and irregular compared with standard tiles, so a bond strong enough to resist movement is important for long-term durability outdoors. Proper substrate slope for drainage and adequate curing time before the patio is used both contribute to a lasting installation alongside the right Roff adhesive.

Which Roff adhesive is suited to heavy natural stone flooring?

Roff Non-Skid Adhesive (NSA) is built for fixing natural stones alongside clay, terracotta and vitrified tiles on floors, making it a suitable choice for heavier natural stone flooring where strong grip and load-bearing bond strength matter. Natural stone can vary in weight, porosity and surface finish, so proper substrate preparation and the correct trowel notch size are especially important for these installations. Once laid, Tenax stone-care products such as Tenax Proseal can be used to seal and protect the finished natural stone surface from staining.

Which Roff adhesive works for heavy natural stone feature walls?

Roff Extrofix Ultra, with its high-tensile-strength formulation for areas prone to vibration, is well suited to heavy natural stone feature walls, where the adhesive must hold significant stone weight securely on a vertical surface over time. Feature walls using natural stone place more stress on an adhesive bond than typical ceramic wall tiling, so both correct substrate preparation and a high-performance adhesive matter. Roff Master Fix is another option worth considering where the wall substrate itself is metal, plywood or cement board rather than plastered masonry.

Which tile adhesive is suitable for underfloor heating systems?

Roff Yogafix Adhesive, being highly polymer-modified and highly flexible, is well suited to underfloor heating systems because the flooring above heating elements undergoes regular expansion and contraction as temperatures change during heating cycles. A rigid, plain cement-based bond is more likely to crack under this repeated thermal movement, whereas Yogafix’s flexibility is designed to accommodate it while maintaining strong adhesion. It’s also important to follow the heating system manufacturer’s guidance on curing and initial heat-up timing before subjecting the new tile installation to full heating cycles.